Master MGH3000 Installationshandbuch PDF herunterladen (Seite 6)

106813

PORTABLE GASOLINE GENERATORS

GROUND FAULT CIRCUIT

INTERRUPTER RECEPTACLE

All models (Except HWI3000) have a 120-

volt ground fault circuit interrupter (GFCI)

receptacle. The GFCI receptacle is on the

control panel or top cover of alternator (models

MGH3000G, MGH3000, and MGH3000PR

only). The GFCI protects you against hazard-

ous electrical shock caused when your body

becomes a path through which electricity

travels to reach ground. This could happen

when you touch an appliance or cord that

is ‘live’ through faulty mechanism, damp or

worn insulation, etc.

When protected by the GFCI, you may still

feel a shock, but the GFCI should cut it off

quickly. A person in normal health should

not receive serious injury. Note: Infants and

very small children may still be affected.

Test Procedure

Check the GFCI receptacle every month.

This insures it is working right.

1. Push black TEST button. Red RESET

button should pop out. This should trip

GFCI, resulting in no electrical power

at receptacle. Verify this by plugging

test lamp with good bulb into recep

tacle. If lamp does not work, GFCI

receptacle is good.

120/240 VOLT

Position

120 VOLT ONLY

Position

Figure 3 - Full Power Selector Switch

GENERATOR

FEATURES

OIL ALERT SYSTEM

The oil alert system protects the engine from

low oil damage. This system automatically

shuts down the engine and prevents engine

restarting if the oil level falls too low.

Note: When this happens, the engine switch

remains in the ON position. The oil alert

system is wired into the ON/OFF Switch.

If this system shuts down the engine, the

engine will not start until you add oil. Add

oil to engine (see Engine Oil, page 7).

Note: Operate generator on a level surface.

If not level, the oil may ﬂow away from the

oil level sensing device. This will cause the

oil alert system to shut down engine.

See engine owner’s manual for more

information.

Figure 2 - Engine Switch Location

HONDA

OFF

START

ENGINE SW

CIRCUIT

BREAKER

ON/push OFF

FULL POWER SELECTOR

SWITCH

All models except HWI3000, MGH3000G,

MGH3000, MGH3000PR, MGH6500IE,

and MGH10000A have a full power selec-

tor switch on the control panel. The switch

has two positions: 120 VOLT ONLY, and

120/240 VOLT.

120 VOLT ONLY: This position sends full

power to the 120V receptacles only. 240V

power is not available. Use this position

when powering 120V items only.

120/240 VOLT: This position sends full power

to the 120/240V receptacle. It also powers the

120V receptacles at reduced wattage capacity.

IMPORTANT: Do not move the full power se-

lector switch while powering electrical items.

Unplug all items before moving switch. Failure

to do so can damage switch. Models HWI3000,

MGH3000G, MGH3000, MGH3000PR,

MGH6500IE, and MGH10000A do not have

this switch. These models provide full power

to all receptacles.

ELECTRIC START

(Models MGH5000DIE,

MGH6500IE, and MGH10000A)

Models MGH5000DIE, MGH6500IE,

and MGH10000A have electric starters.

A battery is not supplied with generator.

You must provide a 12-volt, 32-amp-hour

battery. For more battery information, see

Battery, page 8.

ENGINE SW

OFF

Models HWI3000,

MGH3000G, MGH3000,

MGH4000C, MGH4000CI,

MGH5000D, MGH5000DI,

MGH6000D, and

MGH6000DI

Models

MGH5000DIE,

MGH6500IE, and

MGH10000A

AUTO-IDLE SYSTEM

The Auto-Idle System allows the engine to idle

down or run at a slower speed when the gen-

erator is not being used to supply power. The

Auto-idle system can be turned ON or OFF by

a rocker switch on the control panel. When the

switch is in the OFF position, the engine runs

at full speed all of the time. When the switch

is in the ON position, the engine slows down

to idle speed until an electrical load is applied.

When a load is applied to the generator (an

electrical item is plugged in and turned on) the

engine speeds up to the preset speed required

to produce the correct voltage.

IMPORTANT: A minimum current load

of 1 Amp is required to disengage the auto

idle solenoid and cause the engine to come

up to speed for correct voltage. Powering

items at reduced engine speed will damage

generator and powered items.

WARNING: If RESET button

does not pop out, do not use the

GFCI receptacle. Contact a quali

ﬁed electrician for repairs.

Model

MGH3000PR

1 2 3 4 5 6 7 8 9 10 11 ... 35 36

Kommentare zu diesen Handbüchern

Keine Kommentare

Master MGH3000 Installationshandbuch Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Stromgeneratoren Master MGH3000